Single cage induction motor

Single cage induction motor belongs to an electromechanical machine or prime-mover model. It links electrical torque and flux with rotor speed, angle, mechanical power, or actuator dynamics, making it central to frequency, voltage, and rotor-angle stability studies.

Typical use

  • Use it when electrical transients must interact with rotating mass or machine controls.

  • Initialize torque, power, flux, and speed consistently with the solved power flow.

This model represents a single-cage induction motor in phase-domain EMT form.

Scope and model level

This is the Level-2 induction-motor model. It has a three-wire ABC stator interface and transforms terminal quantities internally to stationary \alpha\beta coordinates. It represents stator and rotor electromagnetic transients together with shaft acceleration, while omitting zero-sequence and detailed mechanical train modes.

Use it for ordinary motor starting, stalling, fault recovery, voltage-dip, and aggregate motor-load studies when one rotor cage adequately represents the machine.

State equations

The state vector contains stator flux, rotor flux, and normalized rotor speed. Representative equations are

\dot\psi_{s,\alpha}=v_\alpha-r_si_{s,\alpha},
\qquad
\dot\psi_{s,\beta}=v_\beta-r_si_{s,\beta},

\dot\psi_{r,\alpha}=-r_ri_{r,\alpha}-\omega_{r,e}\psi_{r,\beta},
\qquad
\dot\psi_{r,\beta}=-r_ri_{r,\beta}+\omega_{r,e}\psi_{r,\alpha}.

Currents are obtained algebraically by inverting the stator/rotor inductance relation. Electromagnetic torque and shaft speed follow

T_e=\frac{3}{2}\omega_{base}
(\psi_{s,\alpha}i_{s,\beta}-\psi_{s,\beta}i_{s,\alpha}),

\dot\omega_r=\frac{T_e-T_m-d(\omega_r-1)}{2h+\varepsilon},
\qquad
s=1-\omega_r.

The mechanical load torque varies quadratically with speed around its nominal value.

Initialization

The model builds a positive-sequence equivalent circuit from the solved three-phase P, Q, and voltage. It estimates and bounds the initial slip, then initializes currents, fluxes, rotor speed, electromagnetic torque, and mechanical torque at a compatible operating point. Large initial derivatives or a power mismatch normally indicate inconsistent motor data, bases, or load-flow sign conventions.

Numerical and physical limits

The model assumes a symmetrical three-phase machine even though the EMT terminal voltages may become unbalanced during the simulation. Resistances, leakage reactances, magnetizing reactance, and inertia must be positive. Severe voltage depressions can drive the motor toward stall; check speed, slip, current, and torque together rather than interpreting terminal power alone.

Interface table

Category

Name

Meaning

Units

Input

v_A

Instantaneous phase-A terminal voltage applied to the motor stator

pu

Input

v_B

Instantaneous phase-B terminal voltage applied to the motor stator

pu

Input

v_C

Instantaneous phase-C terminal voltage applied to the motor stator

pu

Output

i_A

Phase-A current injected by the motor model into the EMT network

pu

Output

i_B

Phase-B current injected by the motor model into the EMT network

pu

Output

i_C

Phase-C current injected by the motor model into the EMT network

pu

Variable

psi_s_alpha

Alpha-axis stator flux linkage state

pu

Variable

psi_s_beta

Beta-axis stator flux linkage state

pu

Variable

psi_r_alpha

Alpha-axis rotor flux linkage state

pu

Variable

psi_r_beta

Beta-axis rotor flux linkage state

pu

Variable

omega_r

Rotor electrical speed state

pu

Variable

i_s_alpha

Alpha-axis stator current derived from the flux states

pu

Variable

i_s_beta

Beta-axis stator current derived from the flux states

pu

Variable

i_r_alpha

Alpha-axis rotor current derived from the rotor flux states

pu

Variable

i_r_beta

Beta-axis rotor current derived from the rotor flux states

pu

Variable

P_motor

Instantaneous three-phase active power absorbed by the motor

pu

Variable

Q_motor

Instantaneous three-phase reactive power absorbed by the motor

pu

Variable

T_e

Electromagnetic torque produced by the motor

pu

Variable

T_m

Mechanical load torque opposing the electromagnetic torque

pu

Variable

slip

Rotor slip relative to synchronous speed

pu

Parameter

r_s

Stator resistance

pu

Parameter

r_r

Rotor resistance

pu

Parameter

x_ls

Stator leakage reactance

pu

Parameter

x_lr

Rotor leakage reactance

pu

Parameter

x_m

Magnetizing reactance

pu

Parameter

h

Inertia constant of the motor shaft system

s

Parameter

d

Mechanical damping coefficient

pu torque/pu speed

Parameter

omega_base

Base electrical angular frequency used to scale the state equations

rad/s

Parameter

t_load_nom

Nominal mechanical load torque used by the internal load model

pu

Parameter

p0_a

Initial phase-A active-power operating point used for initialization

pu

Parameter

p0_b

Initial phase-B active-power operating point used for initialization

pu

Parameter

p0_c

Initial phase-C active-power operating point used for initialization

pu

Parameter

q0_a

Initial phase-A reactive-power operating point used for initialization

pu

Parameter

q0_b

Initial phase-B reactive-power operating point used for initialization

pu

Parameter

q0_c

Initial phase-C reactive-power operating point used for initialization

pu

How to use it

  1. Connect all three stator phases and map the machine data on a consistent base.

  2. Initialize from a converged power flow and verify that total P and Q match the intended motor demand.

  3. Inspect initial slip, speed, torque, and phase currents before applying events.

  4. Use the double-cage model when startup or deep-slip rotor behavior cannot be fitted with one cage.

  5. Perform a time-step convergence check for starts, faults, and near-stall cases.